Difference between revisions of "Data Challenges"

From CMB-S4 wiki
Jump to: navigation, search
Line 17: Line 17:
 
'''[[Sky Models]]'''
 
'''[[Sky Models]]'''
  
To build the sky models the experiment bandpasses are already required.
 
So far nominal tophat bands are being used - a complete list of the center and width is
 
[https://docs.google.com/spreadsheets/d/1K3eqctftHE5fY36uCa_i9mwoCbyKG4o8P9eR5pib7ng in this spreadsheet].
 
The CMB-S4 specific band list is [[CMB-S4 frequency bands v1.99]].
 
What a tophat bandpass actually means is a little tricky and discussed in [[Bandpass Convention - What does flat mean]].
 
It seems that models 00/05/08/09 use nu^-2 in spectral radiance (SR) units, while models 01/02/03 use nu^0 in SR units. (What 06 uses is not known.)
 
 
=== Sky model 00 ===
 
This is simply LCDM + Gaussian dust + Gaussian Sync.
 
Since the dust and sync levels are set to the levels found in the BICEP/Keck field it wouldn't make any sense to use this model for a large sky fraction.
 
 
=== Sky Model 01 ===
 
This is [https://arxiv.org/abs/1608.02841 PySM] run in a1d1f1s1 mode - i.e. with the default settings for AME, dust, free-free and synchrotron.
 
 
=== Sky Model 02 ===
 
This is [https://arxiv.org/abs/1608.02841 PySM] run in a2d4f1s3 mode - [https://github.com/bthorne93/PySM GitHub] for some description of what this means.
 
 
=== Sky Model 03 ===
 
Versus 02 this switches the dust model to a Hensley/Draine model and is dubbed a2d7f1s3. (02 to 03 also marks the switch from pysm_1.0 to pysm_2.0 so the s2, f1, s3 components in principle change. Think the change is to do with the details of how the bandpass integration is being handled.)
 
 
=== Sky Model 04 ===
 
This model switches the dust model to a Tuhin Ghosh provided model which implements dust decorrelation. See [[HiDPol|HI-based dust polarization model for r forecasts]].
 
The AME, sync and free-free components remain the same as 03
 
 
=== Sky Model 05 ===
 
This is a toy model of dust which is highly decorrelated. See [[Toy highly decorrelated dust model]].
 
There is NO AME/sync/Free-free - only dust.
 
 
=== Sky Model 06 ===
 
This is a model from Raphael Flauger and Brandon Hensley based on [https://arxiv.org/abs/1705.01912 MHD sims] of galactic magnetic field populated with dust and relativistic electrons according to this recipe: [[File:sky_models.pdf]].
 
 
=== Sky Model 08 ===
 
This is the model 06 with an alternate electron energy spectrum which gives a synchrotron spectrum closer to reality.
 
 
=== Sky Model 09 ===
 
This is the [[Vansyngel Model]].
 
  
 
== Sim Data Sets ==
 
== Sim Data Sets ==

Revision as of 18:56, 5 February 2018

At the SLAC meeting it was agreed to separate "experiment definitions" (bands, resolutions, sensitivity level) from "sky models" (LCDM+dust+sync+). Each of these will be designated by a number. The combination of a given experiment definition XX acting on a given sky model YY will be designated XX.YY.

Experiment models, sky models and the datasets obtained by applying for former to the latter will be stored at NERSC at
/project/projectdirs/cmbs4/{expt_xx, sky_yy, data_xx.yy}

Experiment Definitions

Experiment Definitions

Input Sky Components

Sky Components

Sky Models

Sky Models


Sim Data Sets

Many of the possible xx.yy combinations have been generated and are available on NERSC.

Most of 02.00 through 02.09 exist - these are the "Science Book config".

Most of 04.00 through 04.06 exist - these are the "CDT report config".

NERSC Info

Shared space is available on NERSC, where everyone is welcome to sign-up for an account under the "Data Analysis for Post-Planck CMB Experiments" allocation (PI Borrill). The files are located in the shared CMB-S4 file space (/project/projectdirs/cmbs4). In order to manage this space, all files stored there should be owned by the cmbs4 project account but accessible to the cmbs4 group. To do this:

  • log in to the cmbs4 project account following the instructions [here]
  • sync the files to an appropriate subdirectory in the project space
  • ensure that the permissions are set appropriately (g+rX,o-rwx)

Remember to include a README and to post the details on this wiki page.

For any NERSC issues, including access to the filegroup and/or project account, please contact Julian Borrill.